As a new to fishing, you may have some confusion about how to put a weight on a fishing line? Why we have to use the fishing line and even where to put it.
If this is something, you don’t know about to before it can be puzzling. Using a sinker or weighted line can be considered as a strange method of fishing. If it can reel in more fish with the attractive aesthetics of the hook, it could be the extremely successful style of fishing. Therefore, Hooking and weighting a line can be a complicated task.
From this article, You will learn everything which you need about fishing weights and how to put them with best fishing reel. Besides, you will realize the reason to use weights and carry out.
What Are Fishing Weights?
Fishing weights are that element which attaches to your line to keep momentum and can make distance when casting. Especially, it ensures the hook and baits sink to a wanted depth after cast rather than floating at the top even there where lass fishes possible to see it.
Particularly you need this when you want to catch big fish that swim deeper down; you require your lure to drop at the depth.
Why Should You Have Weights on Your Fishing Line?
Mostly, the necessity of weights depends on what kind of fish you want to catch and what type of lure you bring to hunt this.
If you are searching for a fish that occupies the bottom of the lake and you are using a pretty light lure, then you have to add enough weight. Because it will ensure the line drops to the bottom. On the other hand, if you want to hunt a fish that only goes for baits, you would add weight. Due to this weight, the baits will move around the water.
How to attach a Weight to a Fishing Line
To complete this how-to, you’re going to require some equipment like
- Fishing pole
- Needle nose pliers
Additionally, you will need a fishing line and sturdy rubber bands. Besides, you should have a pair of scissors to finish the method. Once you got all, you can start then.
In this part, you are going to know about How to put a split shot on a fishing line step by step.
1. Split shot on fishing line– Step by step
- Step 1: Firstly, put the fishing line into the groove of the split shot sinker that is angle almost side of it. If you did not place the sinker on the exact place on your line, it would not be capable of adjusting.
- Step 2: After that, you have to use a pair of pliers to press down on the sinker upright to the groove. As a result, it closes around your fishing line. Be aware and don’t break your line. Also, make sure it is squeezed tight.
- Step 3: Hold the sinker in one hand and then lightly tug the line with the other hand. Make sure it’s on accurately and doesn’t move. If it loses, it will spend your lead sinker flying individually from your line through the cast.
2. Rubber Core on fishing line – Step by step
- Step 1: Burst the line into the rubber groove. Make sure you have done it correctly as after complete you will not able to adjust the position easily.
- Step 2: Then, each rubber ears twist in opposite directions like you were unwrapping a candy. As a result, the line acquires wrapped around the sinker core.
- Step 3: Finally, hold the sinker in one hand and the line in the other hand. Let’s give it a slight pull to ensure that it has absorbed the line correctly. If it moves, you have to undo and have to re-do
3. Ring Loop and Eye (tied sinker) – Step by step
- Step 1: Eliminate, or ignore adding any lure, hooks to the end of your line. Let’s feed the tip of the fish throughout the eye of the sinker. Following, drag the sinker up the line to anywhere you wish to be.
- Step 2: Again, tie one or two-step knot around the sinker bottom where the line went through to lock the set.
- Step 3: check out you have the lead on your fishing line so that you can join your kook. Pull the sinker on the line to ensure it doesn’t fall since this will need you later with your bait and hook. If it moves, re-tie until lock it in securely.
Tips for Putting Weights on Fishing Lines
Firstly, you should know how to hook a fishing line? Take your line you are going to put it through the eyelet of the hook grab the tag end make yourself a loop twist a bit of time there where the line meets the hook itself take the tag end of your line, and you are going to put that through that loop in the string then lay it alongside you hook. Dropped it trays it again and pinch that with your thumb and pull the light-tight.
Hare comes to a question how far should the weight be from the hook? And the answer is: Place one or two split shot sinkers 2–3 inches (5.1–7.6 cm) above the hook. Therefore, it does not make any fault with it once in the water, causing fish not to bite or the hook not to catch.
As always, make sure you have an active license before starting the trip. If you want to make a broad knowledge, read more about how to put a weight on a fishing line. Keep in mind; practice makes perfect. So, get out and gather your knowledge.
Hunting fish with weight can make it most comfortable when you are in search of a safe and robust cast and reel. I hope this article helps all those who enjoy fishing to get both fun and success your next time out in the river, in the sea or the lake.